• 本站微信：bfzyw168 点击关注

    企业信息

    苏州奇辑化工有限公司

  • 10
  • 公司认证： 营业执照已认证
  • 企业性质：私营企业
    成立时间：2004
  • 公司地址： 江苏省 苏州 昆山市 花桥镇 花安路171号1号楼1017室
  • 姓名： 李生
  • 认证： 手机未认证 身份证已认证 微信未绑定

    供应分类

    友情链接

    Sabic PC LEXAN 144R 通用级PC聚碳酸酯

  • 所属行业：塑料 通用/工程塑料 工程塑料
  • 发布日期：2018-04-18
  • 阅读量：229
  • 价格：面议
  • 产品规格：25KG/包
  • 产品数量：10000.00 千克
  • 包装说明：原厂原包
  • 发货地址：江苏苏州昆山市  
  • 关键词：聚碳酸酯,LEXAN,144R,通用级PC

    Sabic PC LEXAN 144R 通用级PC聚碳酸酯详细内容

    LEXAN 144R 沙伯基础创新塑料

    LEXAN 144R物性表：

    Property
     
    TYPICAL PROPERTIES (1)
    MECHANICAL Value Unit Standard
    Tensile Stress, yld, Type I, 50 mm/min 62 MPa ASTM D 638
    Tensile Stress, brk, Type I, 50 mm/min 68 MPa ASTM D 638
    Tensile Strain, yld, Type I, 50 mm/min 7 % ASTM D 638
    Tensile Strain, brk, Type I, 50 mm/min 130 % ASTM D 638
    Tensile Modulus, 50 mm/min 2370 MPa ASTM D 638
    Flexural Stress, yld, 1.3 mm/min, 50 mm span 97 MPa ASTM D 790
    Flexural Modulus, 1.3 mm/min, 50 mm span 2340 MPa ASTM D 790
    Hardness, Rockwell M 70 - ASTM D 785
    Hardness, Rockwell R 118 - ASTM D 785
    Taber Abrasion, CS-17, 1 kg 10 mg/1000cy ASTM D 1044
    Tensile Stress, yield, 50 mm/min 63 MPa ISO 527
    Tensile Stress, break, 50 mm/min 70 MPa ISO 527
    Tensile Strain, yield, 50 mm/min 6 % ISO 527
    Tensile Strain, break, 50 mm/min 110 % ISO 527
    Tensile Modulus, 1 mm/min 2350 MPa ISO 527
    Flexural Stress, yield, 2 mm/min 90 MPa ISO 178
    Flexural Modulus, 2 mm/min 2300 MPa ISO 178
    IMPACT Value Unit Standard
    Izod Impact, unnotched, 23°C 3204 J/m ASTM D 4812
    Izod Impact, notched, 23°C 801 J/m ASTM D 256
    Izod Impact, notched (natural, tints) 801 J/m ASTM D 256
    Izod Impact, notched (colors) 801 J/m ASTM D 256
    Tensile Impact, Type S 577 kJ/m2 ASTM D 1822
    Falling Dart Impact (D 3029), 23°C 169 J ASTM D 3029
    Instrumented Impact Energy @ peak, 23°C 63 J ASTM D 3763
    Izod Impact, unnotched 80*10*4 +23°C NA kJ/m2 ISO 180/1U
    Izod Impact, unnotched 80*10*4 -30°C NA kJ/m2 ISO 180/1U
    Izod Impact, notched 80*10*4 +23°C 12 kJ/m2 ISO 180/1A
    Izod Impact, notched 80*10*4 -30°C 10 kJ/m2 ISO 180/1A
    Charpy Impact, notched, 23°C 35 kJ/m2 ISO 179/2C
    Charpy 23°C, Unnotch Edgew 80*10*4 sp=62mm NA kJ/m2 ISO 179/1eU
    Charpy -30°C, Unnotch Edgew 80*10*4 sp=62mm NA kJ/m2 ISO 179/1eU
    THERMAL Value Unit Standard
    Vicat Softening Temp, Rate B/50 154 °C ASTM D 1525
    HDT, 0.45 MPa, 6.4 mm, unannealed 137 °C ASTM D 648
    HDT, 1.82 MPa, 6.4 mm, unannealed 132 °C ASTM D 648
    CTE, -40°C to 95°C, flow 6.84E-05 1/°C ASTM E 831
    Specific Heat 1.25 J/g-°C ASTM C 351
    Thermal Conductivity 0.19 W/m-°C ASTM C 177
    Thermal Conductivity 0.2 W/m-°C ISO 8302
    CTE, 23°C to 80°C, flow 7.E-05 1/°C ISO 11359-2
    Ball Pressure Test, 125°C +/- 2°C PASSES - IEC 60695-10-2
    Vicat Softening Temp, Rate A/50 153 °C ISO 306
    Vicat Softening Temp, Rate B/50 141 °C ISO 306
    Vicat Softening Temp, Rate B/120 142 °C ISO 306
    HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm 136 °C ISO 75/Be
    HDT/Ae, 1.8 MPa Edgew 120*10*4 sp=100mm 125 °C ISO 75/Ae
    Relative Temp Index, Elec 130 °C UL 746B
    Relative Temp Index, Mech w/impact 130 °C UL 746B
    Relative Temp Index, Mech w/o impact 130 °C UL 746B
    PHYSICAL Value Unit Standard
    Specific Gravity 1.2 - ASTM D 792
    Specific Volume 0.83 cm3/g ASTM D 792
    Density 1.19 g/cm3 ASTM D 792
    Water Absorption, 24 hours 0.15 % ASTM D 570
    Water Absorption, equilibrium, 23C 0.35 % ASTM D 570
    Water Absorption, equilibrium, 100°C 0.58 % ASTM D 570
    Mold Shrinkage, flow, 3.2 mm (5) 0.5 - 0.7 % SABIC Method
    Melt Flow Rate, 300°C/1.2 kgf 10.5 g/10 min ASTM D 1238
    Melt Volume Rate, MVR at 300°C/1.2 kg 10 cm3/10 min ISO 1133
    OPTICAL Value Unit Standard
    Light Transmission, 2.54 mm 88 % ASTM D 1003
    Haze, 2.54 mm 1 % ASTM D 1003
    Refractive Index 1.586 - ASTM D 542
    ELECTRICAL Value Unit Standard
    Volume Resistivity >1.E+17 Ohm-cm ASTM D 257
    Dielectric Strength, in air, 3.2 mm 14.9 kV/mm ASTM D 149
    Relative Permittivity, 50/60 Hz 3.17 - ASTM D 150
    Relative Permittivity, 1 MHz 2.96 - ASTM D 150
    Dissipation Factor, 50/60 Hz 0.0009 - ASTM D 150
    Dissipation Factor, 1 MHz 0.01 - ASTM D 150
    Hot Wire Ignition {PLC) 2 PLC Code UL 746A
    High Voltage Arc Track Rate {PLC} 2 PLC Code UL 746A
    High Ampere Arc Ign, surface {PLC} 1 PLC Code UL 746A
    Comparative Tracking Index (UL) {PLC} 2 PLC Code UL 746A
    Volume Resistivity >1.E+15 Ohm-cm IEC 60093
    Surface Resistivity, ROA >1.E+15 Ohm IEC 60093
    Dielectric Strength, in oil, 3.2 mm 17 kV/mm IEC 60243-1
    Relative Permittivity, 1 MHz 2.7 - IEC 60250
    Dissipation Factor, 50/60 Hz 0.001 - IEC 60250
    Dissipation Factor, 1 MHz 0.01 - IEC 60250
    Relative Permittivity, 50/60 Hz 2.7 - IEC 60250
    FLAME CHARACTERISTICS Value Unit Standard
    UL Recognized, 94HB Flame Class Rating (3) 1.47 mm UL 94
    Oxygen Index (LOI) 25 % ASTM D 2863
    Oxygen Index (LOI) 25 % ISO 4589
    Source GMD, last updated:2006/11/30
    Processing


    Parameter
    Injection Molding Value Unit
    Drying Temperature 120 °C
    Drying Time 3 - 4 hrs
    Drying Time (Cumulative) 48 hrs
    Maximum Moisture Content 0.02 %
    Melt Temperature 295 - 315 °C
    Nozzle Temperature 290 - 310 °C
    Front - Zone 3 Temperature 295 - 315 °C
    Middle - Zone 2 Temperature 280 - 305 °C
    Rear - Zone 1 Temperature 270 - 295 °C
    Mold Temperature 70 - 95 °C
    Back Pressure 0.3 - 0.7 MPa
    Screw Speed 40 - 70 rpm
    Shot to Cylinder Size 40 - 60 %
    Vent Depth 0.025 - 0.076 mm


    FXD921A WH8C104X
    GR1210
    HF1110
    HF1130
    HF1130R
    HP4-1H111
    HPX4 1H8A005T
    HPX8R NA8A005T
    IR2240-111
    LF1520A-111
    LGK4010-731L
    LS1-6164
    LS2-414LT
    ML4351R-80118
    ML6411-76701
    ML765-222(粉)
    ML9330 BK1E519
    OQ1022-111
    OQ1030-111S
    PC0700
    PK2870
    PK2870-21317
    PXL943 GY
    SP7602 GY2220
    VR2220-111
    XHT2143 BK1C141
    XHT3143 NA6D004T


    http://h111222333.cn.b2b168.com
    欢迎来到苏州奇辑化工有限公司网站， 具体地址是江苏省苏州昆山市花安路171号1号楼1017室，联系人是李生。 主要经营PPS,PPA,PC,PC/ABS,PEI 13360669666。 单位注册资金单位注册资金人民币 100 万元以下。 公司供应塑料生产厂家,塑胶厂家价格,工程塑料报价,通用塑料厂家,三菱化学Durabio价格,免喷涂塑料哪家好等产品，始终坚持“用户至上、质量**”的原则，追赶同类产品中优惠的价格、上乘的质量、快捷的方式，为广大用户提供更**的服务。如果你对我们的产品感兴趣，快快来电咨询订购！