企业信息

    苏州奇辑化工有限公司

  • 10
  • 公司认证： 营业执照已认证
  • 企业性质：私营企业
    成立时间：2004
  • 公司地址： 江苏省 苏州 昆山市 花桥镇 花安路171号1号楼1017室
  • 姓名： 李生
  • 认证： 手机未认证 身份证已认证 微信未绑定

    供应分类

    友情链接

    中高流动性PCSabic LEXAN HPS1R医疗级塑料PC基础创新美国

  • 所属行业：塑料 通用/工程塑料 工程塑料
  • 发布日期：2018-04-18
  • 阅读量：197
  • 价格：面议
  • 产品规格：25KG/包
  • 产品数量：30000.00 千克
  • 包装说明：原厂原包
  • 发货地址：江苏苏州昆山市  
  • 关键词：PC塑料,中高流动性,LEXAN,HPS1R,医疗级

    中高流动性PCSabic LEXAN HPS1R医疗级塑料PC基础创新美国详细内容

    Sabic LEXAN HPS1R

    Med/high flow polycarbonate. For medical devices and pharmaceutical applications. Healthcare management of change, biocompatible (ISO10993 or USP Class VI). EtO, e-beam and gamma sterilizable. Higher amount of mold release than HPS1. 

    中高流动性，医疗级塑料PC



    Sabic LEXAN HPS1R物性表

    Property
     
    TYPICAL PROPERTIES (1)
    MECHANICAL Value Unit Standard
    Tensile Stress, yld, Type I, 50 mm/min 630 kgf/cm2 ASTM D 638
    Tensile Stress, brk, Type I, 50 mm/min 660 kgf/cm2 ASTM D 638
    Tensile Strain, yld, Type I, 50 mm/min 6 % ASTM D 638
    Tensile Strain, brk, Type I, 50 mm/min 120 % ASTM D 638
    Tensile Modulus, 50 mm/min 24200 kgf/cm2 ASTM D 638
    Flexural Stress, yld, 1.3 mm/min, 50 mm span 940 kgf/cm2 ASTM D 790
    Flexural Modulus, 1.3 mm/min, 50 mm span 23500 kgf/cm2 ASTM D 790
    Hardness, Rockwell M 70 - ASTM D 785
    Hardness, Rockwell R 118 - ASTM D 785
    Taber Abrasion, CS-17, 1 kg 10 mg/1000cy ASTM D 1044
    Tensile Stress, yield, 50 mm/min 63 MPa ISO 527
    Tensile Stress, break, 50 mm/min 50 MPa ISO 527
    Tensile Strain, yield, 50 mm/min 6 % ISO 527
    Tensile Strain, break, 50 mm/min 70 % ISO 527
    Tensile Modulus, 1 mm/min 2350 MPa ISO 527
    Flexural Stress, yield, 2 mm/min 90 MPa ISO 178
    Flexural Modulus, 2 mm/min 2300 MPa ISO 178
    Hardness, H358/30 95 MPa ISO 2039-1
    IMPACT Value Unit Standard
    Izod Impact, unnotched, 23°C 326 cm-kgf/cm ASTM D 4812
    Izod Impact, notched (natural, tints) 65 cm-kgf/cm ASTM D 256
    Izod Impact, notched (colors) 10 - 65 cm-kgf/cm ASTM D 256
    Tensile Impact, Type S 385 cm-kgf/cm2 ASTM D 1822
    Falling Dart Impact (D 3029), 23°C 1728 cm-kgf ASTM D 3029
    Instrumented Impact Energy @ peak, 23°C 553 cm-kgf ASTM D 3763
    Izod Impact, unnotched 80*10*4 +23°C NB kJ/m2 ISO 180/1U
    Izod Impact, unnotched 80*10*4 -30°C NB kJ/m2 ISO 180/1U
    Izod Impact, notched 80*10*4 +23°C 12 kJ/m2 ISO 180/1A
    Izod Impact, notched 80*10*4 -30°C 10 kJ/m2 ISO 180/1A
    Charpy 23°C, V-notch Edgew 80*10*4 sp=62mm 12 kJ/m2 ISO 179/1eA
    Charpy -30°C, V-notch Edgew 80*10*4 sp=62mm 10 kJ/m2 ISO 179/1eA
    THERMAL Value Unit Standard
    HDT, 0.45 MPa, 6.4 mm, unannealed 137 °C ASTM D 648
    HDT, 1.82 MPa, 6.4 mm, unannealed 126 °C ASTM D 648
    CTE, -40°C to 95°C, flow 6.84E-05 1/°C ASTM E 831
    Specific Heat 1.25 J/g-°C ASTM C 351
    Thermal Conductivity 0.19 W/m-°C ASTM C 177
    Thermal Conductivity 0.2 W/m-°C ISO 8302
    CTE, 23°C to 80°C, flow 7.E-05 1/°C ISO 11359-2
    Ball Pressure Test, 125°C +/- 2°C PASSES - IEC 60695-10-2
    Vicat Softening Temp, Rate B/50 139 °C ISO 306
    Vicat Softening Temp, Rate B/120 140 °C ISO 306
    HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm 133 °C ISO 75/Be
    HDT/Ae, 1.8 MPa Edgew 120*10*4 sp=100mm 121 °C ISO 75/Ae
    PHYSICAL Value Unit Standard
    Specific Gravity 1.2 - ASTM D 792
    Specific Volume 0.83 cm3/g ASTM D 792
    Density 1.19 g/cm3 ASTM D 792
    Water Absorption, 24 hours 0.15 % ASTM D 570
    Water Absorption, equilibrium, 23C 0.35 % ASTM D 570
    Water Absorption, equilibrium, 100°C 0.58 % ASTM D 570
    Mold Shrinkage, flow, 3.2 mm (5) 0.5 - 0.7 % SABIC Method
    Melt Flow Rate, 300°C/1.2 kgf 25 g/10 min ASTM D 1238
    Density 1.2 g/cm3 ISO 1183
    Melt Volume Rate, MVR at 300°C/1.2 kg 23 cm3/10 min ISO 1133
    OPTICAL Value Unit Standard
    Light Transmission, 2.54 mm 88 % ASTM D 1003
    Haze, 2.54 mm 1 % ASTM D 1003
    Refractive Index 1.586 - ASTM D 542
    ELECTRICAL Value Unit Standard
    Volume Resistivity >1.E+17 Ohm-cm ASTM D 257
    Dielectric Strength, in air, 3.2 mm 14.9 kV/mm ASTM D 149
    Relative Permittivity, 50/60 Hz 3.17 - ASTM D 150
    Relative Permittivity, 1 MHz 2.96 - ASTM D 150
    Dissipation Factor, 50/60 Hz 0.0009 - ASTM D 150
    Dissipation Factor, 1 MHz 0.01 - ASTM D 150
    Volume Resistivity >1.E+15 Ohm-cm IEC 60093
    Surface Resistivity, ROA >1.E+15 Ohm IEC 60093
    Dielectric Strength, in oil, 3.2 mm 17 kV/mm IEC 60243-1
    Relative Permittivity, 1 MHz 2.7 - IEC 60250
    Dissipation Factor, 50/60 Hz 0.001 - IEC 60250
    Dissipation Factor, 1 MHz 0.01 - IEC 60250
    Relative Permittivity, 50/60 Hz 2.7 - IEC 60250
    FLAME CHARACTERISTICS Value Unit Standard
    Oxygen Index (LOI) 25 % ISO 4589
    Source GMD, last updated:2000/01/04
    Processing


    Parameter
    Injection Molding Value Unit
    Drying Temperature 120 °C
    Drying Time 3 - 4 hrs
    Drying Time (Cumulative) 48 hrs
    Maximum Moisture Content 0.02 %
    Melt Temperature 270 - 295 °C
    Nozzle Temperature 265 - 290 °C
    Front - Zone 3 Temperature 270 - 295 °C
    Middle - Zone 2 Temperature 260 - 280 °C
    Rear - Zone 1 Temperature 250 - 270 °C
    Mold Temperature 70 - 95 °C
    Back Pressure 0.3 - 0.7 MPa
    Screw Speed 40 - 70 rpm
    Shot to Cylinder Size 40 - 60 %
    Vent Depth 0.025 - 0.076 mm


    500-7040
    500-7388
    500-739
    500ECR BK6A237
    500ECR BL6A237L
    500ECR GY8002L
    500ECR GY90200
    500ECR WH
    500ECR WH9A459L
    500ECR-131/739
    500ECR-739L BK
    500ECR-BK
    500R
    500R-131
    500R-731
    500R-73234
    500R-739
    500R-73966
    500R-13021
    500R-GY
    500R-V0
    5030R-739
    503R
    503R-111
    503R-131
    503R-739
    503R-834
    503R-GY
    505R
    510
    550R-739
    5832C
    5901R
    732-999
    752-336-001
    752-732-999


    http://h111222333.cn.b2b168.com
    欢迎来到苏州奇辑化工有限公司网站， 具体地址是江苏省苏州昆山市花安路171号1号楼1017室，联系人是李生。 主要经营PPS,PPA,PC,PC/ABS,PEI 13360669666。 单位注册资金单位注册资金人民币 100 万元以下。 公司供应塑料生产厂家,塑胶厂家价格,工程塑料报价,通用塑料厂家,三菱化学Durabio价格,免喷涂塑料哪家好等产品，始终坚持“用户至上、质量**”的原则，追赶同类产品中优惠的价格、上乘的质量、快捷的方式，为广大用户提供更**的服务。如果你对我们的产品感兴趣，快快来电咨询订购！