-
苏州奇辑化工有限公司
主营：塑料生产厂家,塑胶厂家价格,工程塑料报价,通用塑料厂家,三菱化学Durabio价格,免喷涂塑料哪家好
苏州奇辑化工有限公司
主营：塑料生产厂家,塑胶厂家价格,工程塑料报价,通用塑料厂家,三菱化学Durabio价格,免喷涂塑料哪家好
9
型号 ：Sabic PC LEXAN 201R
生产厂家：沙伯基础创新
应用级别：注塑级
LEXAN 201R物性表：
Property
TYPICAL PROPERTIES (1)
MECHANICAL
Value
Unit
Standard
Tensile Stress, yld, Type I, 50 mm/min
62
MPa
ASTM D 638
Tensile Stress, brk, Type I, 50 mm/min
68
MPa
ASTM D 638
Tensile Strain, yld, Type I, 50 mm/min
7
%
ASTM D 638
Tensile Strain, brk, Type I, 50 mm/min
135
%
ASTM D 638
Flexural Stress, yld, 1.3 mm/min, 50 mm span
97
MPa
ASTM D 790
Flexural Modulus, 1.3 mm/min, 50 mm span
2340
MPa
ASTM D 790
Hardness, Rockwell M
70
-
ASTM D 785
Hardness, Rockwell R
118
-
ASTM D 785
Taber Abrasion, CS-17, 1 kg
10
mg/1000cy
ASTM D 1044
IMPACT
Value
Unit
Standard
Izod Impact, unnotched, 23°C
3204
J/m
ASTM D 4812
Izod Impact, notched, 23°C
907
J/m
ASTM D 256
Tensile Impact, Type S
630
kJ/m2
ASTM D 1822
Falling Dart Impact (D 3029), 23°C
169
J
ASTM D 3029
Instrumented Impact Energy @ peak, 23°C
64
J
ASTM D 3763
THERMAL
Value
Unit
Standard
Vicat Softening Temp, Rate B/50
154
°C
ASTM D 1525
HDT, 0.45 MPa, 6.4 mm, unannealed
137
°C
ASTM D 648
HDT, 1.82 MPa, 6.4 mm, unannealed
132
°C
ASTM D 648
CTE, -40°C to 95°C, flow
6.84E-05
1/°C
ASTM E 831
Specific Heat
1.25
J/g-°C
ASTM C 351
Thermal Conductivity
0.29
W/m-°C
ASTM C 177
Relative Temp Index, Elec
130
°C
UL 746B
Relative Temp Index, Mech w/impact
130
°C
UL 746B
Relative Temp Index, Mech w/o impact
130
°C
UL 746B
PHYSICAL
Value
Unit
Standard
Specific Gravity
1.2
-
ASTM D 792
Specific Volume
0.83
cm3/g
ASTM D 792
Density
1.19
g/cm3
ASTM D 792
Water Absorption, 24 hours
0.15
%
ASTM D 570
Water Absorption, equilibrium, 23C
0.35
%
ASTM D 570
Water Absorption, equilibrium, 100°C
0.58
%
ASTM D 570
Mold Shrinkage, flow, 3.2 mm (5)
0.5 - 0.7
%
SABIC Method
Melt Flow Rate, 300°C/1.2 kgf
7
g/10 min
ASTM D 1238
OPTICAL
Value
Unit
Standard
Light Transmission, 2.54 mm
88
%
ASTM D 1003
Haze, 2.54 mm
1
%
ASTM D 1003
Refractive Index
1.586
-
ASTM D 542
ELECTRICAL
Value
Unit
Standard
Volume Resistivity
>1.E+17
Ohm-cm
ASTM D 257
Dielectric Strength, in air, 3.2 mm
14.9
kV/mm
ASTM D 149
Relative Permittivity, 50/60 Hz
3.17
-
ASTM D 150
Relative Permittivity, 1 MHz
2.96
-
ASTM D 150
Dissipation Factor, 50/60 Hz
0.0009
-
ASTM D 150
Dissipation Factor, 1 MHz
0.01
-
ASTM D 150
Hot Wire Ignition {PLC)
2
PLC Code
UL 746A
High Voltage Arc Track Rate {PLC}
2
PLC Code
UL 746A
High Ampere Arc Ign, surface {PLC}
1
PLC Code
UL 746A
Comparative Tracking Index (UL) {PLC}
2
PLC Code
UL 746A
FLAME CHARACTERISTICS
Value
Unit
Standard
UL Recognized, 94V-2 Flame Class Rating (3)
1.09
mm
UL 94
UL Recognized, 94V-0 Flame Class Rating (3)
5.99
mm
UL 94
UV-light, water exposure/immersion
F2
-
UL 746C
Source GMD, last updated:2000/01/04
Processing
| Parameter | ||
| Injection Molding | Value | Unit |
| Drying Temperature | 120 | °C |
| Drying Time | 3 - 4 | hrs |
| Drying Time (Cumulative) | 48 | hrs |
| Maximum Moisture Content | 0.02 | % |
| Melt Temperature | 310 - 330 | °C |
| Nozzle Temperature | 305 - 325 | °C |
| Front - Zone 3 Temperature | 310 - 330 | °C |
| Middle - Zone 2 Temperature | 300 - 320 | °C |
| Rear - Zone 1 Temperature | 290 - 310 | °C |
| Mold Temperature | 80 - 115 | °C |
| Back Pressure | 0.3 - 0.7 | MPa |
| Screw Speed | 40 - 70 | rpm |
| Shot to Cylinder Size | 40 - 60 | % |
| Vent Depth | 0.025 - 0.076 |
mm |